The QAudioFormat class stores audio stream parameter information. More...
| Header: | #include <QAudioFormat> |
| qmake: | QT += multimedia |
| enum | Endian { BigEndian, LittleEndian } |
| enum | SampleType { Unknown, SignedInt, UnSignedInt, Float } |
| QAudioFormat() | |
| QAudioFormat(const QAudioFormat &other) | |
| ~QAudioFormat() | |
| QAudioFormat::Endian | byteOrder() const |
| qint32 | bytesForDuration(qint64 duration) const |
| qint32 | bytesForFrames(qint32 frameCount) const |
| int | bytesPerFrame() const |
| int | channelCount() const |
| QString | codec() const |
| qint64 | durationForBytes(qint32 bytes) const |
| qint64 | durationForFrames(qint32 frameCount) const |
| qint32 | framesForBytes(qint32 byteCount) const |
| qint32 | framesForDuration(qint64 duration) const |
| bool | isValid() const |
| int | sampleRate() const |
| int | sampleSize() const |
| QAudioFormat::SampleType | sampleType() const |
| void | setByteOrder(QAudioFormat::Endian byteOrder) |
| void | setChannelCount(int channels) |
| void | setCodec(const QString &codec) |
| void | setSampleRate(int samplerate) |
| void | setSampleSize(int sampleSize) |
| void | setSampleType(QAudioFormat::SampleType sampleType) |
| bool | operator!=(const QAudioFormat &other) const |
| QAudioFormat & | operator=(const QAudioFormat &other) |
| bool | operator==(const QAudioFormat &other) const |
The QAudioFormat class stores audio stream parameter information.
An audio format specifies how data in an audio stream is arranged, i.e, how the stream is to be interpreted. The encoding itself is specified by the codec() used for the stream.
In addition to the encoding, QAudioFormat contains other parameters that further specify how the audio sample data is arranged. These are the frequency, the number of channels, the sample size, the sample type, and the byte order. The following table describes these in more detail.
| Parameter | Description |
|---|---|
| Sample Rate | Samples per second of audio data in Hertz. |
| Number of channels | The number of audio channels (typically one for mono or two for stereo) |
| Sample size | How much data is stored in each sample (typically 8 or 16 bits) |
| Sample type | Numerical representation of sample (typically signed integer, unsigned integer or float) |
| Byte order | Byte ordering of sample (typically little endian, big endian) |
This class is typically used in conjunction with QAudioInput or QAudioOutput to allow you to specify the parameters of the audio stream being read or written, or with QAudioBuffer when dealing with samples in memory.
You can obtain audio formats compatible with the audio device used through functions in QAudioDeviceInfo. This class also lets you query available parameter values for a device, so that you can set the parameters yourself. See the QAudioDeviceInfo class description for details. You need to know the format of the audio streams you wish to play or record.
In the common case of interleaved linear PCM data, the codec will be "audio/pcm", and the samples for all channels will be interleaved. One sample for each channel for the same instant in time is referred to as a frame in Qt Multimedia (and other places).
| Constant | Value | Description |
|---|---|---|
QAudioFormat::BigEndian |
QSysInfo::BigEndian |
Samples are big endian byte order |
QAudioFormat::LittleEndian |
QSysInfo::LittleEndian |
Samples are little endian byte order |
| Constant | Value | Description |
|---|---|---|
QAudioFormat::Unknown |
0 |
Not Set |
QAudioFormat::SignedInt |
1 |
Samples are signed integers |
QAudioFormat::UnSignedInt |
2 |
Samples are unsigned intergers |
QAudioFormat::Float |
3 |
Samples are floats |
Construct a new audio format.
Values are initialized as follows:
codec() = ""
Construct a new audio format using other.
Destroy this audio format.
Returns the current byteOrder value.
See also setByteOrder().
Returns the number of bytes required for this audio format for duration microseconds.
Returns 0 if this format is not valid.
Note that some rounding may occur if duration is not an exact fraction of the sampleRate().
See also durationForBytes().
Returns the number of bytes required for frameCount frames of this format.
Returns 0 if this format is not valid.
See also bytesForDuration().
Returns the number of bytes required to represent one frame (a sample in each channel) in this format.
Returns 0 if this format is invalid.
Returns the current channel count value.
See also setChannelCount().
Returns the current codec identifier.
See also setCodec() and QAudioDeviceInfo::supportedCodecs().
Returns the number of microseconds represented by bytes in this format.
Returns 0 if this format is not valid.
Note that some rounding may occur if bytes is not an exact multiple of the number of bytes per frame.
See also bytesForDuration().
Return the number of microseconds represented by frameCount frames in this format.
Returns the number of frames represented by byteCount in this format.
Note that some rounding may occur if byteCount is not an exact multiple of the number of bytes per frame.
Each frame has one sample per channel.
See also framesForDuration().
Returns the number of frames required to represent duration microseconds in this format.
Note that some rounding may occur if duration is not an exact fraction of the sampleRate().
Returns true if all of the parameters are valid.
Returns the current sample rate in Hertz.
See also setSampleRate().
Returns the current sample size value, in bits.
See also setSampleSize() and bytesPerFrame().
Returns the current SampleType value.
See also setSampleType().
Sets the byteOrder to byteOrder.
See also byteOrder().
Sets the channel count to channels.
See also channelCount().
Sets the codec to codec.
The parameter to this function should be one of the types reported by the QAudioDeviceInfo::supportedCodecs() function for the audio device you are working with.
See also codec() and QAudioDeviceInfo::supportedCodecs().
Sets the sample rate to samplerate Hertz.
See also sampleRate().
Sets the sample size to the sampleSize specified, in bits.
This is typically 8 or 16, but some systems may support higher sample sizes.
See also sampleSize().
Sets the sampleType to sampleType.
See also sampleType().
Returns true if this QAudioFormat is not equal to the other QAudioFormat; otherwise returns false.
All elements of QAudioFormat are used for the comparison.
Assigns other to this QAudioFormat implementation.
Returns true if this QAudioFormat is equal to the other QAudioFormat; otherwise returns false.
All elements of QAudioFormat are used for the comparison.
